Marmitek RC840 Specifiche Pagina 25
- Pagina / 112
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Disarming cancels both active arming modes.
3.7.6: Forced Arming
Forced arming enables you to arm the system when the system is not ready. For
example, if a door protected by a magnetic contact is open, you may arm the system on
condition that the door will be closed by the end of the Exit delay. If the door is still open
after the exit delay expires, an alarm is generated.
Two conditions enable you to perform Forced arming:
x Forced arming is enabled – see section 9.3.1: Forced Arm.
x The sensor that is causing the System Not Ready condition is Force
Arm enabled – see section 7.6.5: Force Arm.
3.7.7: Instant Arming
Instant arming is a feature that allows you to cancel the entry delay after Part or
Perimeter arming the system. For this feature to function, it must be enabled in
programming – see 9.3.4: Instant Arm.
To instantly arm the system.
1. Check if the system is ready to arm.
2. Press the Part or Perimeter arming key on the keypad and enter your
user code if One-Key Arming is disabled.
3. Press and hold down on your keypad until the message Instant
Arming, OK? is displayed
4. Press 3; the exit delay for the current arming period is cancelled.
3.7.8: Disarming
When a sensor is tripped, the entry delay counts down; each arming method has its own
entry delay.
To disarm the system:
x Enter a valid user code.
1
If the Cancel Alarm feature is enabled (see 9.18: Cancel Alarm), disarming the system
within five minutes of an alarm causes the control panel to send an Alarm Cancelled event
to the monitoring station. In this case, a message is displayed on the keypads’ LCD and
the control panel does not allow any local function to be performed until
9
is pressed for
confirmation.
3.8: Remote Arming/Disarming via SMS
You can arm and disarm the system remotely by sending the SMS commands from a
cellular phone to the cellular communications module. Additionally, you can check the
arm status of the system by sending an Arm Status request message.
Each SMS command contains the following elements:
X SMS Command Descriptor (up to 43 characters of free text)
Y # (delimiter – separates the descriptor from the actual command)
Z User Code (4 digits)
[ Command (120=Disarm, 121=Full Arm, 122=Part Arm, 123=Perimeter Arm,
124=Full + Perimeter Arm, 125=Part + Perimeter Arm, 200 = Arm Status)
The following example shows the format of an SMS command for arming the system:
ProGuard800™ -25-
- Safety Warnings 2
- Table of Contents 3
- ProGuard800™ -5 5
- Chapter One: Introduction 6
- 1.2: Specifications 7
- 1.3: System Overview 7
- 1.4: Hardware Layout 9
- Figure 1.3: Main Board 10
- ProGuard800™ -11 11
- ProGuard800™ -13 13
- 2.2: Installation Procedure 14
- ProGuard800™ -15 15
- 2.3: Back Tamper 17
- 3.1: Front Panel Layout 19
- 3.2: System Status LEDs 19
- 3.3: Front Panel Keypad 20
- 3.4: LCD Display 20
- ProGuard800™ -21 21
- 3.7: Arming/Disarming 23
- ProGuard800™ -25 25
- FuLl A r m#1234121 26
- FULL A RM ED- M A RK 26
- ProGuard800™ -27 27
- 4.1: Menu Navigation 28
- 4.2: Stop Communications 28
- 4.4: User Codes 29
- 4.5: Follow Me 31
- 4.6: Event Log 31
- 4.7: Service Menu 32
- ProGuard800™ -33 33
- ZONE #2 34
- ProGuard800™ -35 35
- 5.1: Incoming Calls 37
- 5.2: Outgoing Calls 39
- ProGuard800™ -41 41
- 6.1: Keypad Control 42
- 6.2: Keyfob Control 42
- 6.3: Telephone Control 42
- 6.4: Scheduling 43
- Table 6.1: Weekly Schedule 44
- Chapter Seven: Devices 45
- 7.4: Supervision Time 46
- 7.5: Re-Synchronization 46
- 7.6: Zones 46
- ProGuard800™ -47 47
- 7.7: Keyfobs 49
- 7.8: Keypads 50
- 7.9: Repeaters 51
- 7.10: Wireless Siren 51
- 8.1: Entry/Exit Delay 53
- 8.2: Arm on Exit 53
- 8.4: Entry Deviation 54
- 8.5: Exit Restart 54
- 8.6: Arming Tones 54
- 8.7: Home Automation Tones 55
- 8.8: System Trouble Tones 55
- 8.9: Tones Options 56
- Chapter Nine: System Options 57
- 9.4: Panic Alarm 59
- 9.5: AC Loss Delay 59
- 9.6: Display Options 60
- 9.7: PGM Output Options 61
- 9.9: “No Arm” Indication 62
- 9.10: Jamming Detection 62
- 9.11: “No Motion” Time 63
- 9.13: Vocal Messages 63
- 9.14: Installer Access 63
- 9.16: Daylight Savings 64
- 9.17: Report Fail Trouble 64
- 9.18: Cancel Alarm 64
- 9.20: Verified Fire 65
- 9.21: Battery Type 65
- Chapter Ten: Communications 66
- ProGuard800™ -67 67
- 10.3: Vocal Message Dialler 68
- ProGuard800™ -69 69
- 10.4: Remote Programming 70
- ProGuard800™ -71 71
- 10.5: Service Call 72
- 10.6: Communications Options 72
- ProGuard800™ -73 73
- 10.7: GSM Options 75
- ProGuard800™ -77 77
- ProGuard800™ -79 79
- 11.1: X-10 Overview 80
- 11.2: HA Units 80
- ProGuard800™ -81 81
- 11.3: House Code 83
- 11.4: HA Control 83
- 12.1: Initialization 84
- 12.3: Clear User Codes 84
- 12.5: Find Modules 85
- Appendix A: Menu Structure 86
- ProGuard800™ -87 87
- ProGuard800™ -89 89
- ProGuard800™ -91 91
- PIR Sensors (MS845) 93
- ProGuard800™ -95 95
- Magnetic Contact (DS831) 96
- ProGuard800™ -97 97
- Glass break Sensor (GB843) 99
- Figure B.7: GB843 (cover off) 100
- ProGuard800™ -101 101
- Smoke Detector (SD833) 102
- Keyfobs (PR811/KR814) 103
- Figure B.13: WK820 104
- Figure B.14: RC840 104
- ProGuard800™ -105 105
- Transmitter Specifications 106
- Appendix C: Event Table 107
- Appendix D: Zone Types 109
- Declaration of Conformity 111
Prodotti e manuali riguardandi Sistemi di controllo di accesso Marmitek RC840
(68 pagine)
Vernier Video and Logger Pro Guide manuels
Manuels d'utilisation et guides de l'utilisateur pour Équipement Vernier Video and Logger Pro Guide.
Nous fournissons des manuels en pdf 1 Vernier Video and Logger Pro Guide à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commenti su questo manuale