Marmitek SC9000 Guida Utente Pagina 36
- Pagina / 44
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Comfort Remote Control SH624 – 4x AAA batteries
Wanneer de indicator op de SH624 zwak gaat branden, dienen de batterijen vervangen te worden.
• If the indicator light on the SH624 is not very bright, the batteries should be replaced.
• First set the switch on the front of the remote control to SEC. Now open the battery compartment on the back of the remote
control and replace the batteries within 30 seconds.
• If the console does not respond to your remote control after replacing the batteries, press the PANIC button on your remote
control. You now need to reregister the remote control, using the procedure described in 3.1.2.
☺ To avoid losing a memory space, you can remove the old code for your remote control from the memory (see 8.2).
Door/Window Sensor DS90 – 2x AAA batteries
The console checks the battery status of the DS90 sensor. If the batteries are too weak, the console will indicate a ‘PROBLEM’ and
the zone number will flash.
• Normally the unique code of the sensor will remain in the memory (if you replace the batteries within 30 seconds). After
replacing the batteries you can check whether the sensor still has its unique code. You do this by opening the door or window.
If the sensor has remembered its code, the console display will read ZONE x OPEN (zone number for x). If nothing happens, the
door/window sensor needs to be reregistered (see 4.1.3). Delete zones you do not use anymore (see 9.7) or install the sensor in
the same zone as before.
Motion Detector MS90 – 2x AA batteries
The console checks the battery status of the MS90 sensor. If the batteries are too weak, the console will indicate a ‘PROBLEM’ and
the zone number will flash.
• Normally the unique code of the sensor will remain in the memory (if you replace the batteries within 30 seconds). You can
check this by setting your system to ARMED AWAY. If the sensor has remembered its code, the alarm will go off when you
walk past the sensor. If nothing happens, you need to reregister the motion detector (see 4.2.3). Delete the zone (see 9.8) and
reregister the sensor (see 4.2.3).
13.Frequently asked questions
Why does the security system not work?
Check whether you see any text on the console display. If not: check whether the AC adapter is connected to the mains, whether
the electrical wire is plugged into the adapter and whether the plug is connected to the console.
Check whether you can control the system via the console. If so, check whether the remote control works by checking whether
the control indicator on the remote control flashes when you press e.g. the ARM button.
Change the batteries if necessary and reinstall the remote control.
What to do if a zone indicator flashes slowly?
One of the sensors or motion detectors has not contacted the base console for a longer time. Check the batteries in the sensor or
motion detector. Erase the zone and reregister the sensor. Move the sensor so that the signal can reach the console.
If an error is found while setting the alarm, you will hear a repeated two-tone ‘error signal’. If a sensor indicates there is a
problem (e.g. window opened), you can choose not to activate this sensor.
While the two-tone ‘error signal’ can be heard, you need to press the CLEAR button and reset the alarm. The zone indicator of
the sensor concerned flashes quickly.
What to do if a zone indicator flashes quickly?
You have pressed the CLEAR button to activate the security system while a sensor or motion detector indicated an error. Solve the
problem (i.e. close the window, replace the batteries) before activating the zone.
EXTRA OPTIONS
36 MARMITEK
20071_20090424_UG_SC9000_EN 30-07-2009 09:10 Pagina 36
- SAFEGUARD 1
- TOTALGUARD 1
- 2 MARMITEK 2
- 3SAFEGUARD / TOTALGUARD 3
- Introduction 4
- Safety warnings 4
- Marmitek SafeGuard-system 5
- Marmitek TotalGuard-systeem 6
- 2. The security 7
- 2.1 Installing the console 8
- 2.3 The menus 9
- BASIC OPTIONS 10
- 7. OPTIONS 10
- 3. Installing remote controls 12
- 4. Installing the sensors 14
- 4.2 Motion Detector MS90 15
- 5.1 Setting the clock 17
- 5.2 Storing phone numbers 18
- 6. Using the security system 19
- 6.2 Panic alarm 20
- 6.4 Disarming the system 21
- 6.5 Error messages 21
- 7.1 Introduction 22
- 7.2 Addressing your modules 23
- 7.8 Setting the timer 24
- EXTRA OPTIONS 26
- 9.2 Activating the chime 27
- 9.3 Using wired inputs 28
- 10.4 Transceiver function 31
- 11. Telephone functions 34
- 12.Changing the batteries 35
- 13.Frequently asked questions 36
- 37SAFEGUARD / TOTALGUARD 37
- TABEL SENSORS 38
- TABEL TELEPHONE NUMBERS 38
- TECHNICAL DATA 39
- DECLARATION OF CONFORMITY 40
Prodotti e manuali riguardandi Sistemi di controllo di accesso Marmitek SC9000
(28 pagine)
(29 pagine)Sony CXS-2100 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Nie Sony CXS-2100.
Dostarczamy 1 pdf podręczników Sony CXS-2100 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Commenti su questo manuale